Wassel battery

[gp200ts1]

Looking for a slim battery for my Wassel conversion. Thing is to put it where I want it can't be more than 50mm wide. What are others using and anyone know of thin batteries of 5amp plus?

[Toddy]

I use one of these , bit wider than what you want though

http://www.blueboxbatteries.co.uk/batte ... ry/12v-4ah

[Nelly]

There's all sorts of sizes of sealed lead acid batteries here....
http://www.battery-force.co.uk/category ... eries.html

[terryj]

i just brought an alarm battery of amazon i think sized to fit my battery tray and a bodged up clamp

[citydaz]

I spent many hours loooking for that elusive thin / small battery that would fit in my tool box without taking up too much room.
In the end I got this: 12N5-3B 12V 5Ah Yuasa Motorcycle Battery.
It was the best compromise between small size and and Ah.
It important that you have proper screw on terminals rather than the slide on type as your wires will keep slipping off.

cheers & good luck!

citydaz

[Toddy]

I spent many hours loooking for that elusive thin / small battery that would fit in my tool box without taking up too much room.
In the end I got this: 12N5-3B 12V 5Ah Yuasa Motorcycle Battery.
It was the best compromise between small size and and Ah.
It important that you have proper screw on terminals rather than the slide on type as your wires will keep slipping off.

cheers & good luck!

citydaz

I have slip on terminals if their covered and a good fit never had an issue

[rossclark]

I spent many hours loooking for that elusive thin / small battery that would fit in my tool box without taking up too much room.
In the end I got this: 12N5-3B 12V 5Ah Yuasa Motorcycle Battery.
It was the best compromise between small size and and Ah.
It important that you have proper screw on terminals rather than the slide on type as your wires will keep slipping off.

cheers & good luck!

citydaz

Exactly the same.

[Donnie]

already replied on scooterotica but

The space

IMG_2857 1 by Donnie Canning, on Flickr

PX Battery tray with side dremelled off and attached to back of toolbox where your air filter normally goes.

IMG_2858 1 by Donnie Canning, on Flickr

bought this http://www.ebay.co.uk/itm/301855488535? ... EBIDX%3AIT

which is a AGM better and service free version of http://www.mdsbattery.co.uk/shop/produc ... oupID=1029 which is what I did have and was tired through being run down

and all fitted.

IMG_2864 1 by Donnie Canning, on Flickr

[gp200ts1]

already replied on scooterotica but

The space

IMG_2857 1 by Donnie Canning, on Flickr

PX Battery tray with side dremelled off and attached to back of toolbox where your air filter normally goes.

IMG_2858 1 by Donnie Canning, on Flickr

bought this http://www.ebay.co.uk/itm/301855488535? ... EBIDX%3AIT

which is a AGM better and service free version of http://www.mdsbattery.co.uk/shop/produc ... oupID=1029 which is what I did have and was tired through being run down

and all fitted.

IMG_2864 1 by Donnie Canning, on Flickr

That's what I've done on my gp but I've ended up with just 50mm to fit a battery into. Found this 12v 5ah battery which will fit but I can't find a stockist yet
It's a numax SLA5-12 it's 140mm long, 48mm wide and 103mm tall so it's an ideal size.